Cable and pipe locator “Success AG-511N”

PARAMETER

ROUTE LOCATION

Frequencies of the receiver’s filter

Main filter frequency 50(60)* / 100(120)* / 512 / 1024 / 8192 / 32768 Hz

«Broadband», (frequency range)

0,05 to 8,2 KHz

Gain factor

100 dB

Visual indication

LED scale (7 values)

Sound indication

Headphones - natural, filtered and synthesized signal

Built-in emitter - synthesized signal

Power supply

Voltage 1,8 to 4V - alkaline batteries АА type 1,5 V (2 pcs.)

Time of continuous operation not less than

10 hours

Operation temperature

-30С…to +50С

Location precision

+\- 0,3 m

Ingress protection rating

IP54

AP-014 receiver dimensions

145 ×70 × 24 mm

Weight of the electronic unit

0,15 kg

The frequencies of the continuous «Co» or pulse «Pu» signal, Hz ± 0,1% - «kHz»

Load «clips» or «clamp»

512 - «0.5» / 1024 - «1.0» / 8192 - «8.2» / 32768 - «33»

«Antenna» modes

8192 - «8.2» / 32768 - «33»

Operating modes

«Antenna» modes

Internal transmitting inductor «In».

External induction transmitting antenna «An».

«Modulation» modes (special form signal)

Pulse «Pu» (short-term transmissions of the sine signals). Transmission duration 0,12sec. Transmissions repetition frequency 1Hz.

Dual-frequency «2F» (simultaneous frequency generation 1024Hz, 8192Hz). Amplitudes ratio 4/1 (respectively).

Output parameters under power supply voltage 12…15V

Output current, А

Restricted by the program under manual increment, ≥

5 – at frequency 512Hz «0.5» / 1024Hz «1.0» / 8192Hz «8.2» / «2F»

3 - at frequency 32768Hz «33»

Set by the program for automatic adjustment with the external load of «clips» or «clamp», ≥

0,2 – at frequency 512Hz «0.5» / 1024Hz «1.0» / «2F»

0,1 – at frequency 8192Hz «8.2» / 32768Hz «33»

Maximum output voltage, V

Depending on «modulation», ≥

32 – in the dual-frequency modulation mode «2F»

40 – in other modes

Maximum output power, W

Restricted by the program, ≥

20 - In the continuous «Co» and pulse «Pu» modes at frequencies 512Hz «0.5» /

1024Hz «1.0» / 8192Hz «8.2» at load resistance up to 80Ω In dual-frequency mode «2F» at load resistance up to 50Ω.

6 - At frequency 32768Hz «33» at load resistance up to 260Ω.

Power supply sources

Operating range of the supply voltages

Minimally acceptable voltage for oscillation start-up - 7V.

Maximum allowed voltage for operation – 15V.

Automatic shutdown voltage in the “oscillation” mode < 4,2V.

Battery set

8 «alkaline» cells 1,5V «type С» Recommended – «Duracell ® ULTRA».

External power supply sources (optional)

Battery «12V» (e.g. automotive) Output voltage 11…14V, maximum current not less than 4А.

Mains power supply adapter АG114М.02.020 (extra accessory based on GS60A15-P1J «MEAN WELL») Output voltage 15V, power 60W.

Operating time («life cycle»)

While in operation of the battery set «type Сх8» is defined by the quality (capacity and «load capability»)

of the applied alkaline cells and can be equal to from 4 to 6 hours in the «Co» и «2F» modes or from

20 to 30 hours in the «Pu» mode at initial output voltage 7W in «continuous» modes «Co» /

«2F» or at initial output voltage 15W in pulse modulation mode «Pu».

Under the external power supply is fully conditioned by this external energy source characteristics

therefore under mains supply operating time is unlimited.

Operational characteristics

An automatic control over the output voltage during oscillation process

Proportional control over the output power depending on the “energy potential” of the power supply source.

Automatic shutdowns of the device

At power supply voltage in the “stop” mode < 6,5V.

At power supply voltage in the “oscillation” mode < 4,2V.

At power supply voltage > 15,5V.

In case of exceeding of the admissible absorbed current value (the exact figure depends on the actual mode).

In case of short circuit of the output during the adjustment process

(actuation of the hardware safety system of the terminal amplifier).

In case of non-compliance of the oscillation mode settings depending on whether the external antenna

 is installed in the output or not (the switch to the “stop” mode).

In case of “long” (≈ 100sec) downtime in the “stop” mode (if the buttons are not pushed).

Adjustment with load

Automatic, up to the reaching of the specific consumption rate or attainment of the load current: - ≥

 0,2А at frequencies 512Hz «0.5» / 1024Hz «1.0» / «2F»; - ≥ 0,1А at frequencies 8192Hz «8.2» и 32768Hz «33».

Manual after the automatic adjustment.

Connection options to the utility under examination

«Contact» connection with “earth return”.

«Non-contact» connection with application of the internal transmitting antenna «In».

«Non-contact» connection with the use of external induction transmitting antenna «An»

(the emission intensity is higher and easier access to the utility in comparison with the internal transmitting antenna «In»).

«Non-contact» connection using the transmitting induction “clamp” (selection of the cable from the bunch is possible).

Structural parameters

Power output amplifier

The technology — updated CLASS D Efficiency to 85%.

LED indicators

Separate light-emitting diodes indicating parameters and modes.

Digital indicator displaying the modes and parameters values and also showing output parameters of the 

«MULTIMETER» measurements, e.g.: output voltage (V), load current (А), load power (W) and load resistance (Ω /kΩ).

Overall dimensions of the electronic unit (case), not more than, mm.

216х180х105mm

The weight of the electronic unit, not more than, kg

2

The admissible environment temperatures range when in operation

- 30°С to +60°С With “battery” power supply it is not recommended to use the device under sub-zero environmental temperatures.

Ingress protection rating

IP65 (when the enclosure-case is shut).